|
CEDAR Digital Torque Driver/Wrench ประแจ/ไขควงวัดแรงแบบดิจิตอล ยี่ห้อ CEDAR |
|
CEDAR Digital Torque Driver/Wrench
ประแจ/ไขควงวัดแรงแบบดิจิตอล ยี่ห้อ CEDAR
| Screw tightening control |
| ● DIGITAL TORQUE DRIVER DID-4 |
  |
(1) Unify the display section and a frame. It became stronger.
(2) Display Measurement Mode, Unit, Etc. on Display Section.
(3) Data Output is USB Form.
(4) Prepare each button in accordance with operation.
Button operation became simple |
*The torque screwdriver is Ergonomic and light weight, yet ruggedly constructed
*Available in: lb-in, kg-cm and N-m
*Peak, Real Time and Peak Down measuring mode (selectable)
*800 data memory.
*Programmable High and Low set points with both audible beep and Green/Red LED indicator for uniform torque tightening or GO/NO GO testing
*Programmable screw tightening counter
*Programmable Auto Zero function resets unit to zero for easy operation
*Both CW and CCW operation
*ASCII format output(USB)
*Runs on internal Ni-MH batteries (for 12 hours) Auto shut-off after 10 min. of non-use
* AC charger and carrying case included. |
| Specification |
DID-4 |
Measuring range
|
0.020 - 4 N-m |
| 0.20～40 kgf-cm |
| 0.20～35 lbf-in |
| Accuracy |
± 0.5% (in case of reading 499 or less = last digit +/- 3 reading) |
| Display |
The 4 figures digital display of LCD |
| The measurement direction |
CW-CCW (right and left) |
Measuring
mode |
P-P Peak |
Holding Peak Load Value |
| T-R Track |
Showing Real time torque value ( Used for Zero-Adjustment ) |
| P-D Peak down |
Holding Load Value at the moment to change from upward to downword |
| C Real-time output |
Load torque value is outputted every about 1/ 160.
|
Decision
function |
Setting of torque value |
Programmable High and Low setpoints with both audible beep and Green/Red LED indicator for uniform torque tightening or GO/NO GO testing |
|
The Maximum, the minimum, and the average value
|
Displays, memory and output the data number, the maximum, the minimum, and the average value of the measured value to 30 data. It can save by a maximum of 10 channels.
|
| Data spec. |
Data transfer |
ASCII format (Baud rate : 19200)
When outputting data,the cable(USB miniB) is needed. |
| Data memory |
800 data / ten channels data
|
| A setup of the number of counts |
One to 99 count (count in a direction with a bundle) |
| Power supply |
Ni-MH chargeable battery 1.2V×4cells 800mAh |
| Auto power save |
10 minutes no use, automatically switch off. |
| Charging time |
From empty - less than 5hours |
| Continunous working time |
12 hours |
| Bit /Socket part |
HEX6.35 |
| Weight |
about 400g |
| Attachment |
Bit （＋） ＃１ ＃２ |
Accessories
(one piece each) |
AC/DC Adaptor (Charger) |
| An inspection report, a proofreading certificate, a traceability system figure |
| ● DIGITAL TORQUE WRENCH DIW-120/75/20/15 |
 |
(1) Unify the display section and a frame. It became stronger.
(2) Display Measurement Mode, Unit, Etc. on Display Section.
(3) Data Output is USB Form.
(4) Prepare each button in accordance with operation.
Button operation became simple |
*The torque screwdriver is Ergonomic and light weight, yet ruggedly constructed
*Available in: lb-in, kg-cm and N-m
*Peak, Real Time and Peak Down measuring mode (selectable)
*800 data memory.
*Programmable High and Low set points with both audible beep and Green/Red LED indicator for uniform torque tightening or GO/NO GO testing
*Programmable screw tightening counter
*Programmable Auto Zero function resets unit to zero for easy operation
*Both CW and CCW operation
*ASCII format output(USB)
*Runs on internal Ni-MH batteries (for 12 hours) Auto shut-off after 10 min. of non-use
* AC charger and carrying case included. |
NEW DEVELOPMENT
Wrench head awivels 300°
 |
| Specification |
DIW-15 |
DIW-20 |
DIW-75 |
DIW-120 |
Measuring range N・m
(at the time of Track) |
0.20 - 15 N･m |
0.20 - 20 N･m |
0.20 - 75 N・m |
2.0 - 120 N・m |
| 2.0～150 kgf・cm |
2.0～200 kgf・cm |
2.0～750 kgf・cm |
20～1200 kgf・cm |
| 2.0～130 lbf・in |
2.0～174 lbf・in |
2.0～650 lbf・in |
20～1040 lbf・in |
| Accuracy |
±0.5% (F/S)
(199 or less digit±1digit) |
±0.5% (F/S)
(499 or less digit±3digit) |
±0.5% (F/S)
(199 or less digit±1digit） |
| Display |
The 4 figures digital display of LCD |
| The measurement direction |
CW-CCW (right and left) |
Measuring
mode |
P-P Peak |
Holding Peak Load Value |
| T-R Track |
Showing Real time torque value ( Used for Zero-Adjustment ) |
| P-D Peak down |
Holding Load Value at the moment to change from upward to downword |
| C Real-time output |
Load torque value is outputted every about1/ 160 second |
Decision
function |
Setting of torque value |
Programmable High and Low setpoints with both audible beep and Green/ Red LED indicator for uniform torque tightening or GO/NO GO testing |
| The Maximum, the minimum, and the average value |
Displays, memory and output the data number, the maximum, the minimum, and the average value of the measured value to 30 data. It can save by a maximum of 10 channels. |
| Data spec. |
Data transfer |
ASCII format (Baud rate : 19200) |
| Data memory |
800 data / ten channels data |
| A setup of the number of counts |
One to 99 count (count in a direction with a bundle) |
| Auto power save |
10 minutes no use, automatically switch off. |
| Charging time |
From empty - less than 5hours |
| Continunous working time |
12 hours |
| Outside size |
φ34(grip)×236(L) |
φ34(grip)×235(L) |
φ34(grip)×320(L) |
φ34(grip)×445(L) |
| Weight (about) |
430g |
470g |
620g |
830g |
| Socket engagement |
6.35 square, including steel ball |
9.5 square, including steel ball |
12.7 square, including steel ball |
| Attachment |
- |
One-way socket |
Accessories
(one piece each) |
AC/DC adaptor |
| An inspection report, a proofreading certificate, a traceability system figure |
For more information please contact :
This e-mail address is being protected from spambots. You need JavaScript enabled to view it
ตัวแทนนำเข้าเครื่องมือวัดและเครื่องมืออุตสาหกรรมชั้นนำโดยตรง
|
|
|
CEDAR Torque Tester/ Electric Screw Driver เครื่องทดสอบแรงบิดไขควงไฟฟ้า ยี่ห้อ CEDAR |
|
CEDAR Torque Tester/ Electric Screw Driver
เครื่องทดสอบแรงบิดไขควงไฟฟ้า ยี่ห้อ CEDAR
| ●Torque Meter DI-9M-8/08 |
DI-9 series is most suitable for checking and controlling the torque of
Electric Screwdriver and Torque Driver. |
|
upgrade The main changed parts
(1) In a display board, "measurement mode", a "measurement unit", "the maximum, the minimum, an average, etc.", etc. display.
(2) Change of Measurement Unit Can be Performed N-m <=> kgf-cm <=>lbf-in Etc.
(3) Setup of Various Numerical Values Can be Easy and Can Carry Out Speedily.
(4) Calculation of Maximum, Minimum, and Average Became Intelligible.
(5) The call of the saved data became easy. The output of data also became intelligible.
(6) Fault charge protection. It is pilot-lamp lighting during charge.
(7) Data Output is USB Form (B Type).
(8) Memory Data are 800 Affairs
(9) Real-time Output is Every 1 / 180 Seconds.
|
 |
  |
|
The best for everyday check of an electric driver
Wide measurement range (0 - 8000digit),
it corresponds to various set torques
Can measure without inversion/
rolling-back work efficiently by OW joint (PAT.P).
|
| Specification |
DI-9M-8 |
DI-9M-08 |
| Measuring range |
0.020-8 N･m |
2.0-800 mN･m |
|
0.20～80 kgf・cm
|
0.020～8 kgf・cm |
| 0.20～70 lbf・in |
0.020～7 lbf・in |
| Accuracy |
±0.5% (499 digit or less ±3digit) |
| Display |
The 4 figures digital display of LCD |
| The measurement direction |
CW-CCW (right and left) |
| Zero return by one touch |
Return to zero by pressing clear button. |
| Measurement Mode |
Track , P-P(peak to peak) , P-D(Peak-Down) , C(Real-time Output)
|
|
High and low limits judging function
|
High and low value are measurement within the limits, and can be set up.
|
| Real-time Output |
Load torque value is outputted every about1/ 180 second.
|
| The Maximum, the minimum, and the average value display |
The maximum, the minimum, average value, and the data number of 30 data are displayed.It saves to ten channels.
|
| Data Output |
ASCII format (baud rate 19200) |
| Auto power save |
10 minutes no use, automatically switch off. |
| Power supply |
Ni-Cd chargeable battery 1.2V × 5cells 700mAh |
| Charging time |
About 3hours |
| Continuous working time |
About 12hours |
| clearance |
It is a display clearance in set-up time. (0.1 - 3.0 sec) |
| Socket size |
□ 20mm/ □9.5mm |
| Dimension / Weight |
W:160×D:125×H:55 / About 1kg |
| Recommend buffer accessories |
Measuring joint
OW-20/OW-60 |
Measuring joint
OW-025/OW-10 |
Cube (with a 5th page screw hole) 20x20x20
(M2.6/M3/M4/M5/M6 Tap processing) |
| AC/DC adaptor |
| Exclusive receipt case |
| An inspection report, a proofreading certificate, a traceability system figure |
※Do not use for measurement of impact tool.Do not apply more than the specified torque.
| ●Torque Meter CD-100M/10M |
 |
upgrade The main changed parts
(1) In a display board, "measurement mode", a "measurement unit", "the maximum, the minimum, an average, etc.", etc. display.
(2) Change of Measurement Unit Can be Performed N-m <=> kgf-cm <=>lbf-in Etc.
(3) Setup of Various Numerical Values Can be Easy and Can Carry Out Speedily.
(4) Calculation of Maximum, Minimum, and Average Became Intelligible.
(5) The call of the saved data became easy. The output of data also became intelligible.
(6) Fault charge protection. It is pilot-lamp lighting during charge.
(7) Data Output is USB Form (B Type).
(8) Memory Data are 800 Affairs
(9) Real-time Output is Every 1 / 180 Seconds. |
| Specification |
CD－100M |
CD－10M |
Measuring range
(at the time of Track) |
0.10～10 N・m |
1.0～100 ｃN・m |
| 1.0～100 kgf・cm |
0.10～10 kgf・cm |
| 1.0～90 lbf・in |
0.10～9 lbf・in |
| Accuracy |
±0.5％（F/S）(199 or less digit±1digit) |
| Display |
The 3.5 figures digital display of LCD |
| The measurement direction |
CW-CCW (right and left) |
| Measurement Mode |
Track , P-P(peak to peak) , P-D(Peak-Down) , C(Real-time Output) |
| High and low limits judging function |
High and low value are measurement within the limits, and can be set up. |
| Real-time Output |
Load torque value is outputted every about1/ 180 second. |
| The Maximum, the minimum, and the average value display |
The maximum, the minimum, average value, and the data number of 30 data are displayed.It saves to ten channels. |
| Automatic Clearance |
Automatically clear the displayed value after certain time
(0.5 - 3.0 sec,selectable at each 0.5 sec).
Setting 0.0 sec for manual Zero clearance |
| One-touch zero |
A clear button is pushed and it is a zero. Data is outputed. |
| Data output |
ASCII format (baud rate 19200) |
| Power supply |
Ni-Cd chargeable battery 1.2V×5cells 700mAh |
| Auto power save |
10 minutes no use, automatically switch off. |
| Charging time |
About 3 hours |
| Continunous working time |
About 12 hours |
| Socket fit mouth |
□ 20mm/ □9.5mm |
| Weight |
Abbreviation 1 kg |
| Outside dimension |
160（W）×125（D）×55（H） |
| Attachment |
Measurement joint SJ50/SJ10K |
Measurement joint SJ10 |
|
Accessories
(one piece each)
|
AC/DC adaptor |
| Exclusive receipt case |
| An inspection report, a proofreading certificate, traceability system figure |
For more information please contact :
This e-mail address is being protected from spambots. You need JavaScript enabled to view it
ตัวแทนนำเข้าเครื่องมือวัดและเครื่องมืออุตสาหกรรมชั้นนำโดยตรง
|
|
|
|
|
|
|